人形の蓮田人形の蓮田

可動フィギュア『蓮田2号』データ ACTION FIGURE<Renda2>DATA

  • ダウンロード商品
    ¥ 2,000

■更新情報 4/16 蓮田2号配信開始  組み立ては以下スレッドを参照お願いします https://x.com/REN_W_HEATPEN/status/1778434062463734167 -------------------- ◎『小さくてよく動く人型の格好いい玩具が欲しい!!』のは変わらず ・10cm前後のサイズ ・玩具としてポーズを色々変えられること ・ラフに扱えたらなど良い。 そんなおもちゃ『蓮田1号』の改良タイプ『蓮田2号』です。 1号よりシュッとしているので特撮ヒーローへの改造に向いています 是非ダウンロードして作成してください! 1号よりリーズナブルになってます。 組み立てマニュアルはおおむね1号と同じです。 ご質問事項ございましたらXアカウント @REN_W_HEATPEN まで。 ご感想もお待ちしております。 ※注意 データでは各部パーツ分割されたSTLファイルになっています。 ご自身でスライサーソフトで出力ををおこない 組み立てることで可動フィギュアとして楽しめます。 ご注意ください。 ※なお、データでは腕・脚・指などは左側しか含まれていません。 右側はCHITUBOXなどでのサポート設定時に複製・反転させてください。 ◎サイズ:高さ11cmくらいのサイズ想定 ◎レジン: 当方で確認済みのレジンとしては以下となります。  ・ショーコレジンスーパータフ:全身どこに使ってもOK!  ・RESIONE ANTI-IMPACT:パンツや胸のガワ部分干渉してまがってもいい箇所関節パーツのオス側、パーツで外側に広がる力がかからないところ  ・SK本舗 高靱性水洗いレジン:固めのパーツ。関節もある程度はOK  ・SK本舗 水洗いレジン:テスト出力として使用してみてもOK     力がかかる箇所はボキボキ折れるので関節はお勧めしません  ・良い素材があったら教えてください!! ◎指可動には 別素材の芯が必要です。 テクノロート0.7mmを使用しております。参考までに ------------------------- ■ご注意 STLデータで購入された方へ ------------------------- 基本的には 著作権利は私RENDERにあります。 無断転載・無断配布・無断販売は禁止します。 構造を参考に作成することはままあることだと思います。 個人的に楽しむ分問題ありませんが 購入されたデータを加工して再配布することは禁止します。 確認できた時点で削除等のお声掛けをさせていただきます。 ---------------------------------------------------- Updates 4/16 REMDA2 distribution begins!  -------------------- ◎"I want a cool toy in humanoid form that is small and moves well!" is still the same Size around 10cm It should be able to change its pose in various ways as a toy. It would be better if it could be handled roughly. This is "Hasuda No. 2," an improved version of the "Hasuda No. 1" toy. It is more shapely than No. 1, so it is suitable for remodeling into a special effects hero! Please download and create it! It is more reasonable than No.1. Translated with DeepL.com (free version) -------------------- The assembly manual is generally the same as the first one. If you have any questions, please contact our X account @REN_W_HEATPEN. We are looking forward to your feedback. *Caution The data is an STL file divided into parts. You can use slicer software to output the data by yourself. and assemble it to enjoy as a movable figure. Please be careful. Note that only the left side of the arms, legs, fingers, etc. are included in the data. The right side should be duplicated and inverted when setting up support in CHITUBOX, etc. ◎Size: Assumed to be about 11 cm in height ◎Resin: The following resins have been confirmed by us.  Shoko Resin Super Tough: Can be used anywhere on the body!  RESIONE ANTI-IMPACT: Can be used on the male side of joint parts and parts that are not subject to outward spreading force, such as pants and chest gussets.  SK Honpo: High toughness washable resin: Hard parts. Joints are OK to some extent.  SK Hompo: Washable resin: Can be used as a test output.     We do not recommend joints because parts that are subjected to force will break.  If you have any good materials, please let me know! ◎Finger mobility requires a core of a different material. We use Technorot 0.7mm. For reference. ------------------------- Note: For those who purchased the data in STL format ------------------------- Basically I, RENDER, own the copyright. Unauthorized reproduction, unauthorized distribution, and unauthorized sale are prohibited. I think that it is a thing to create it referring to the structure as it is. There is no problem for personal enjoyment, but But it is prohibited to process the purchased data and redistribute it. We will ask you to delete the data when we confirm it.

■更新情報 4/16 蓮田2号配信開始  組み立ては以下スレッドを参照お願いします https://x.com/REN_W_HEATPEN/status/1778434062463734167 -------------------- ◎『小さくてよく動く人型の格好いい玩具が欲しい!!』のは変わらず ・10cm前後のサイズ ・玩具としてポーズを色々変えられること ・ラフに扱えたらなど良い。 そんなおもちゃ『蓮田1号』の改良タイプ『蓮田2号』です。 1号よりシュッとしているので特撮ヒーローへの改造に向いています 是非ダウンロードして作成してください! 1号よりリーズナブルになってます。 組み立てマニュアルはおおむね1号と同じです。 ご質問事項ございましたらXアカウント @REN_W_HEATPEN まで。 ご感想もお待ちしております。 ※注意 データでは各部パーツ分割されたSTLファイルになっています。 ご自身でスライサーソフトで出力ををおこない 組み立てることで可動フィギュアとして楽しめます。 ご注意ください。 ※なお、データでは腕・脚・指などは左側しか含まれていません。 右側はCHITUBOXなどでのサポート設定時に複製・反転させてください。 ◎サイズ:高さ11cmくらいのサイズ想定 ◎レジン: 当方で確認済みのレジンとしては以下となります。  ・ショーコレジンスーパータフ:全身どこに使ってもOK!  ・RESIONE ANTI-IMPACT:パンツや胸のガワ部分干渉してまがってもいい箇所関節パーツのオス側、パーツで外側に広がる力がかからないところ  ・SK本舗 高靱性水洗いレジン:固めのパーツ。関節もある程度はOK  ・SK本舗 水洗いレジン:テスト出力として使用してみてもOK     力がかかる箇所はボキボキ折れるので関節はお勧めしません  ・良い素材があったら教えてください!! ◎指可動には 別素材の芯が必要です。 テクノロート0.7mmを使用しております。参考までに ------------------------- ■ご注意 STLデータで購入された方へ ------------------------- 基本的には 著作権利は私RENDERにあります。 無断転載・無断配布・無断販売は禁止します。 構造を参考に作成することはままあることだと思います。 個人的に楽しむ分問題ありませんが 購入されたデータを加工して再配布することは禁止します。 確認できた時点で削除等のお声掛けをさせていただきます。 ---------------------------------------------------- Updates 4/16 REMDA2 distribution begins!  -------------------- ◎"I want a cool toy in humanoid form that is small and moves well!" is still the same Size around 10cm It should be able to change its pose in various ways as a toy. It would be better if it could be handled roughly. This is "Hasuda No. 2," an improved version of the "Hasuda No. 1" toy. It is more shapely than No. 1, so it is suitable for remodeling into a special effects hero! Please download and create it! It is more reasonable than No.1. Translated with DeepL.com (free version) -------------------- The assembly manual is generally the same as the first one. If you have any questions, please contact our X account @REN_W_HEATPEN. We are looking forward to your feedback. *Caution The data is an STL file divided into parts. You can use slicer software to output the data by yourself. and assemble it to enjoy as a movable figure. Please be careful. Note that only the left side of the arms, legs, fingers, etc. are included in the data. The right side should be duplicated and inverted when setting up support in CHITUBOX, etc. ◎Size: Assumed to be about 11 cm in height ◎Resin: The following resins have been confirmed by us.  Shoko Resin Super Tough: Can be used anywhere on the body!  RESIONE ANTI-IMPACT: Can be used on the male side of joint parts and parts that are not subject to outward spreading force, such as pants and chest gussets.  SK Honpo: High toughness washable resin: Hard parts. Joints are OK to some extent.  SK Hompo: Washable resin: Can be used as a test output.     We do not recommend joints because parts that are subjected to force will break.  If you have any good materials, please let me know! ◎Finger mobility requires a core of a different material. We use Technorot 0.7mm. For reference. ------------------------- Note: For those who purchased the data in STL format ------------------------- Basically I, RENDER, own the copyright. Unauthorized reproduction, unauthorized distribution, and unauthorized sale are prohibited. I think that it is a thing to create it referring to the structure as it is. There is no problem for personal enjoyment, but But it is prohibited to process the purchased data and redistribute it. We will ask you to delete the data when we confirm it.